ASME B18.12-2012 机械紧固件术语汇编

作者:标准资料网时间:2024-05-12 13:22:57 浏览:9936 来源:标准资料网

【英文标准名称】:GlossaryofTermsforMechanicalFasteners
【原文标准名称】:机械紧固件术语汇编
【标准号】:ASMEB18.12-2012
【标准状态】:现行
【国别】:美国
【发布日期】:2012-01-01
【实施或试行日期】:
【发布单位】:美国机械工程师协会(US-ASME)
【起草单位】:ASME/B18
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:Bolts;Classificationsystems;Definitions;Designations;Dimensions;Fasteners;Glossaries;Lockingandlocatingdevices;Materials;Mechanicalproperties;Nuts;Pins(nails);Production;Rivets;Screws(bolts);Studs(fasteners);Terminology;Threadforms;Washers
【摘要】:ThisStandardisasummaryofnomenclatureandterminologycurrentlyusedtodefineand/ordescribemechanicalfasteners,relatedcharacteristics,andthemanufacturingprocessesthatproducetheseproducts.
【中国标准分类号】:J13
【国际标准分类号】:01_040_21;21_060_01
【页数】:68P;A4
【正文语种】:英语

下载地址: 点击此处下载

返回跳至顶部

上一篇: ASME B16.18-2012 铸铜合金软钎焊连接压力管件
下一篇: ASME PVHO-1-2012 病员用压力容器安全性标准

【英文标准名称】:SealingsforTonguedandGroovedFlanges;NominalPressure10to160
【原文标准名称】:带槽和键的法兰用平面密封件.公称压力10至160
【标准号】:DIN2691-1949
【标准状态】:作废
【国别】:
【发布日期】:
【实施或试行日期】:
【发布单位】:德国标准化学会(DE-DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:
【摘要】:
【中国标准分类号】:
【国际标准分类号】:
【页数】:
【正文语种】:

Product Code:SAE USCAR27
Title:Specification for Testing Gas Discharge Light Source Subsystem
Issuing Committee:
Scope:This specification is a general level subsystem light source specification that establishes test requirements of a Gas Discharge Light Source (GDLS) subsystem for use on passenger vehicles.The completed test data to this test specification is intended to be provided to the OEM by the Tier one lamp set maker as part of the lamp assembly PPAP. Re-testing shall be required if any portion of the approved GDLS experiences a design, manufacturing or component change.This document shall be applied to systems that meet the requirements for design, performance and validation established by government standards.The subsystem is defined as the ballast, igniter and light source and shall be tested as a subsystem and considered one test sample for the entire test sequence. A failure of any component in the test sample shall constitute a failure of the entire sample. Substitution or replacement of only the light source shall be allowed during testing. Failure of the light source more than once in a tested system shall constitute a failure of the GDLS. If other manufacture驴s components are intended to be approved for use in the GDLS, then those possible combinations of components shall be considered a new GDLS and shall also be tested.Additional testing may be required by individual OEM驴s to meet specific EMC, quality, reliability and durability objectives.The following tests are to be performed under the following conditions:驴New light source (capsule) or ballast design驴Design or process change made to an existing capsule or ballast, which could affect the outcome of the test驴Completion of one calendar year as noted in the 驴ANNUAL TESTS驴 Table shown in the Appendix. (Note: Production process control data, collected at a shorter interval per an approved control plan, may be substituted if approved by customer驴s responsible engineer and purchasing representative.)